Advanced paver solutions

Pave like manholes

don’t exist.

Cut the frame, pull it out of the paving zone, plate it, then mill and pave straight across. The manholes come back to grade after striping, perfectly level, in under thirty minutes each. No stopping the paver. No hits on the mill.

Cut time, per structure
< 0 MIN
Back to grade
< 0 MIN
Less material used
0 %
Cut
Pull
Plate™
Mill right across

The frame is out. The plate takes the hit.

Cut
Pull
Plate
Mill
Pave
Set to grade
Open the lane
Cut
Pull
Plate
Mill
Pave
Set to grade
Open the lane
Faster, smarter, safer

Nothing kills a paving day like a manhole.

You’ve invested in top-notch paving equipment and built a crew you trust. Every minute on the job matters, and every stop to adjust a frame costs you momentum. One bad hit can wreck a milling machine and take the afternoon with it.

You shouldn’t have to fight manholes when you’re trying to pave. So we built a method that takes them out of the way entirely.

Join the growing network of pavers who use the Mr. Manhole Method and finish more jobs in less time.

01

The paver stops

Crews idle while someone raises a frame by hand. The whole train waits on one structure.

02

The mill takes a hit

Teeth, drums, and a day’s schedule, gone on a frame that sat a little high.

03

It fails inspection

A frame set before the mat is guesswork. Low or proud, the city sees it.

04

You come back for it

Callbacks eat labor you already bid. Fix it right once and keep the margin.

The Cut, Pull, Plate™ Method

Three moves before you pave. One after.

Your crew stays focused on what they do best: paving. The manhole work happens around the mat, not in the middle of it.

Under 15 min
01

Cut the manhole in under 15 minutes.

Center the cutter on the lid and take one clean, full-depth circle through asphalt and concrete. Nobody goes in the hole.

Out of the zone
02

Pull the frame clear of the paving zone.

The old frame and chimney lift out in one piece. No jackhammers, no hand digging, nothing left proud for the mill to find.

Mill & pave across
03

Plate it, then mill and pave right over.

A steel plate covers the opening. Your mill and paver run straight through as if the structure isn’t even there.

Under 30 min
04

Set to grade after the striping is done.

Cut through the fresh mat and set the frame to the finished surface, perfectly level every time. No failed inspections, no callbacks.

The value, in hours

Same paving job. Two very different schedules.

A traditional square-cut adjustment runs five hours or more. The Mr. Manhole Method takes about one. Here’s what that looks like on a 24-manhole job.

Manholes on the job
24
Square cut · 5+ hrs each
120 hrs
Mr. Manhole · ~1 hr each
24 hrs
Crew hours back
0
8-hour shifts saved
0
Less debris & material
0 %

Estimate only, based on ~1 hour vs. 5+ hours per structure. We’ll run real numbers with your crew size and structure count.

Patented circular cutting

Corners crack. Circles don’t.

Square cuts leave sharp corners and over-cut edges, planes of weakness that break under impact and freeze-thaw. A round cut spreads the load evenly, so the pavement around the frame lasts as long as the road.

Traditional square cut

5+ HRS
4 planes of weakness

Mr. Manhole round cut

~1 HR
Even load, no corners
Your call

Sub it out, or bring it in-house.

Either way, you take control of the schedule, boost profit, and deliver flawless pavement every time.

Sub it

Hand the manholes to a certified Mr. Manhole installer near your job. They cut, pull, and plate ahead of your mill, then set to grade after striping.

Bring it in-house

Put a cutter on your own skid steer and keep the work, and the margin, on your crew. Buy, finance, or rent while you prove it out.

Oh, and did we mention cities love it too?
Stop losing bids

Cities want roads that last. Give them the spec.

You’re bidding on tight margins with skilled crews and heavy equipment. Municipalities know manholes are among the biggest culprits behind road failures. The contractor who solves that problem wins the job, and the next one.

Mr. Manhole repair specifications are fully engineered and trusted by municipalities nationwide.

OSHA
silica
compliant
01

Perfectly level every time

Frames sit flush with the road. No bumps, no complaints.

02

Stops leakage for good

Seals tight against water infiltration and pavement failure.

03

Built to last

Time-tested and proven in thousands of installs.

04

Reduces labor costs

Fewer steps, faster installs, smaller crews.

05

Keeps crews safer

Designed for safety and OSHA silica-reg compliant.

06

Cleaner finish

A uniform, professional look that stands out on every job.

07

20% less material

Cut precisely and replace only what’s necessary.

08

Fully engineered specs

Backed by engineering standards municipalities trust.

More than a method

A complete system, built to work together.

Precision-grade rings and risers, engineered repair tools, and specifications that hold up to inspection. A proven, repeatable process that cuts labor, improves consistency, and adds to the bottom line on every job.

You’re not just fixing manholes.
You’re upgrading the way you pave.
Frequently asked

Questions pavers ask us.

More answers, install guides, and downloads in the knowledge base.

With the Mr. Manhole Method, you can. Cut, Pull & Plate replaces the frame with a steel plate so you can mill and pave right over it, then come back for a full restoration. You pave like the manhole isn’t there and skip the usual delays.

In most cases, immediately. Precision cutting and minimal material removal leave a stable, level frame. The whole process takes about an hour, so paving resumes in record time.

Faster completion, less excavation and waste, minimal traffic disruption, and real cost reduction. Round-cut technology generates up to 20% less debris and uses up to 20% less replacement material than a square cut, and takes about an hour instead of 5+.

Square cuts leave sharp corners and over-cut areas, planes of weakness that resist impact and freeze-thaw poorly. A circular cut removes them, reducing load points and edge weaknesses for longer-lasting pavement around the manhole.

Get a quote

Tell us what’s on your next paving job. We’ll show you how to get through it faster.

No pressure and no long sales cycle. Give us the structure count and your machine, and we’ll come back with the right setup and the numbers for your season.

Mr. Manhole does more than manholes.

See four ways one system can help your crew do more work, take on more jobs, and make more money.